Technical FAQs

Ask a Question

What are the Forms to add a TeSys T to a starter?

Issue:
What are the forms to add a TeSys T to a starter? And which TeSys T module is used? 

Product Line:
NEMA Type S Starters

Environment:
North American Market 

Cause:
Product Selection

Resolution:

The forms, and devices, used are dependent upon NEMA size, full load amperage, and control voltage. Please see the table below for the forms and part numbers. 
 
NEMA Size Range Communication Protocol Form TeSys T Part Number
Control Voltage Control Voltage
100-240VAC 24VDC 100-240VAC 24VDC
1
 
.4-8 Modbus H612 H712 LTMR08MFM LTMR08MBD
ProfiBus H613 H713 LTMR08PFM LTMR08PBD
CANopen H614 H714 LTMR08CFM LTMR08CBD
DeviceNet H615 H715 LTMR08DFM LTMR08DBD
Ethernet TCP/IP H616 H716 LTMR08EFM LTMR08EBD
1.35-27 Modbus H622 H722 LTMR27MFM LTMR28MBD
ProfiBUS H623 H723 LTMR27PFM LTMR08PBD
CANopen H624 H724 LTMR27CFM LTMR27CBD
DeviceNet H625 H725 LTMR27DFM LTMR27DBD
Ethernet TCP/IP H626 H726 LTMR27EFM LTMR27EBD
2, 3 5.0-100 Modbus H632 H732  LTMR100MFM   LTMR100MBD 
ProfiBus H633 H733 LTMR100PFM LTMR100PBD
CANopen H634 H734 LTMR100CFM LTMR100CBD
DeviceNet H635 H735 LTMR100DFM LTMR100DBD
Ethernet TCP/IP H636 H736 LTMR100EFM LTMR100EBD
4 8-160 (CT 300:5 3 turns) Modbus H652 H752 LTMR08MFM LTMR08MBD
ProfiBus H653 H753 LTMR08PFM LTMR08PBD
CANopen H654 H754 LTMR08CFM LTMR08CBD
DeviceNet H655 H755 LTMR08DFM LTMR08DBD
Ethernet TCP/IP H656 H756 LTMR08EFM LTMR08EBD
5 24-480 (CT 300:5 1 turn) Modbus H662 H762 LTMR08MFM LTMR08MBD
ProfiBus H663 H763 LTMR08PFM LTMR08PBD
CANopen H664 H764 LTMR08CFM LTMR08CBD
DeviceNet H665 H765 LTMR08DFM LTMR08DBD
Ethernet TCP/IP H666 H766 LTMR08EFM LTMR08EBD
6 48-960 (CT 600:5 1 turn)* Modbus H672 H772 LTMR08MFM LTMR08MBD
ProfiBus H673 H773 LTMR08PFM LTMR08PBD
CANopen H674 H774 LTMR08CFM LTMR08CBD
DeviceNet H675 H775 LTMR08DFM LTMR08DBD
Ethernet TCP/IP H676 H776 LTMR08EFM LTMR08EBD


* NEMA size 6 contactors are only rated up to 810 amps (and should not be used for greater than 810 amps), as such when the contactor rating is programmed in to the TeSys T as 810 amps the device will not let you set a full load amperage over 810 amps. 

Note: To order a NEMA starter with a TeSys T motor management controller the product selector should be used. 
Was this helpful?
What can we do to improve the information ?